FTDI Community
General Category => Test and Review Area => Topic started by: FTDI Community on May 27, 2020, 03:42:14 PM
-
Hello,
Customers using macOS 10.15 Catalina have been experiencing signature issues with FTDI's VCP driver.
The following driver should resolve these issues:
FTDIUSBSerialDriver_v2_4_4.dmg (ftp://u45902898-ide:Ftd1$erv@ftp.ftdichip.com/CES/Driver_beta/FTDIUSBSerialDriver_v2_4_4.dmg)
Please let us know if you have any feedback on this driver by either posting here or emailing us at support1@ftdichip.com
Best Regards,
FTDI Community
-
Hi,
I am facing the issues still with this version. I am on macOS Catalina 10.15.5.
If you need any input from my side to provide more value, let me know and I will support.
sudo kextutil /Library/Extensions/FTDIUSBSerialDriver.kext
Password:
Untrusted kexts are not allowed
Kext with invalid signature (-67050) denied: /private/var/db/KernelExtensionManagement/Staging/tmp.MOlSZN/F1E8F36B-1CB8-4356-919C-90DD52584F6C.kext
Bundle (/Library/Extensions/TrimDriver.kext) failed to validate, deleting: /private/var/db/KernelExtensionManagement/Staging/tmp.MOlSZN/F1E8F36B-1CB8-4356-919C-90DD52584F6C.kext
Unable to stage kext (/Library/Extensions/TrimDriver.kext) to secure location.
Warnings:
Dependency lacks appropriate value for OSBundleRequired and may not be available during early boot:
com.apple.iokit.IOSerialFamily - Safe Boot
(kernel) Notice - new kext com.apple.driver.usb.AppleUSBHostPlatformProperties, v1.2 matches prelinked kext but can't determine if executables are the same (no UUIDs).
-
I am having the same issue as @pharmonie with this new driver. I am trying to use the Arduino IDE with a Sparkfun redboard but am completely blocked by this issue. Are there any workarounds?
-
I downloaded and installed the new v2_4_4 driver on a 2020 MacBook Air running Catalina 10.15.6 (on the day it became available).
The new installer ran (I did have to give specific permission in System Preferences) and completed the installation. After the install I could properly communicate with the virtual serial port.
This was a welcome relief since my previous attempts to install the v2_4_2 driver on this machine, with earlier versions of Catalina initially appeared to have worked, but I had not been able to communication with the device, which in my case was a USB-interfaced Digi X-Stream radio modem.
-
This new driver also worked for me. It turns out I was using a charging only USB cable :-[
-
I'm having the same issue. The link above no longer works. Any updates?
-
Same issue Here, 2.4.4. not working with Catalina 10.15.6...
sudo kextutil /Library/Extensions/FTDIUSBSerialDriver.kext
Password:
Warnings:
Dependency lacks appropriate value for OSBundleRequired and may not be available during early boot:
com.apple.iokit.IOSerialFamily - Safe Boot
Disabling KextAudit: SIP is off
(kernel) Notice - new kext com.apple.driver.usb.AppleUSBHostPlatformProperties, v1.2 matches prelinked kext but can't determine if executables are the same (no UUIDs).
-
I have the same warning on Catalina 10.15.7.
$ sudo kextutil /Library/Extensions/FTDIUSBSerialDriver.kext
Password:
Warnings:
Dependency lacks appropriate value for OSBundleRequired and may not be available during early boot:
com.apple.iokit.IOSerialFamily - Safe Boot
(kernel) Notice - new kext com.apple.driver.usb.AppleUSBHostPlatformProperties, v1.2 matches prelinked kext but can't determine if executables are the same (no UUIDs).
I have installed D2XX 1.4.22, D2XXhelper and VCP drivers 2.4.4
The driver is loaded after the above command but I cannot see any devices /dev/tty.usbserialXXX or /dev/cu.usbserialXXX under /dev.
In system information Hardware-> USB I get the following information.
Dual RS232-HS:
Product ID: 0x6010
Vendor ID: 0x0403 (Future Technology Devices International Limited)
Version: 7.00
Speed: Up to 480 Mb/s
Manufacturer: FTDI
Location ID: 0x14220000 / 16
Current Available (mA): 500
Current Required (mA): 500
Extra Operating Current (mA): 0